Whirlpool gold ice maker troubleshooting. Whirlpool Gold Ice Maker not working 2018-10-20

Whirlpool gold ice maker troubleshooting Rating: 5,2/10 1661 reviews

SOLVED: Ice maker stopped making ice.

whirlpool gold ice maker troubleshooting

If you have just installed line and filter you can disconnect the line and run water thru line and filter Answered on Dec 04, 2018. Despite the difference in design, these all use the same type and length of wire, and they all cut an 8 by 8 inch slab of ice. Look to see if you have water to solenoid on back bottom of refrigerator, the go the other side and see if you have water there. If the thermostat sticks for a cycle, the slab is never harvested, chilling continues, and you get the symptoms just listed as a consequence. The first thing to check is that dust on the condenser in the bottom of the unit isn't restricting air flow. The stainless motor bearings are an odd mix of metric-inch sizes but easily replaced if you can find them.

Next

Whirlpool Refrigerator Ice Maker Not Working

whirlpool gold ice maker troubleshooting

It typically results from using acid cleaners that are incompletely rinsed. When this happened to mine, the repairman told me occasionally the ice dispenser push arm loses track where it is in the cycle. I reference these trademarks solely to help you to identify these machines, to understand their various qualities and technical principles, to diagnose their problems, and to inform you of compatibility of my parts and services with various products made by others. The need for this seems to happen to my machine a couple of times a year. Your best defense to this sort of gouge is to study this page carefully, so you can diagnose your machine yourself, or at least you can diagnose the hired diagnostician. It appears there is no clog, but I don't know if an hour with the door open, and freezer empty on the zero setting was enough time.

Next

How Do You Troubleshoot a Whirlpool Refrigerator?

whirlpool gold ice maker troubleshooting

The solution for that is to remove the reservoir bin and trim back that lip just a little. Plug in the power cord, or try another port if the cord is plugged in well. You can use this information to troubleshoot your own refrigerator and then enter your model number into the search box to find the right part that will fit your fridge. These notes will help you fine-tune the settings now and in the future. Remember that you can still make uncut ice slabs while you're awaiting the repair; see '' cutter grid is actually optional''. Before the final tensioning, when you have the wire in place over its circuitous length, carefully inspect each of the wire bends across the plastic insulators to verify that the wire is properly routed across the radius bends provided on the insulators. Check the switch to ensure that it is turned on.

Next

ยป W10757851 Ice Level Optics Board Diagnostics & Replacement

whirlpool gold ice maker troubleshooting

You can disconnect the thermistor and restart the machine to see if the unit operates properly in timed mode. Note that I recommend changing the entire icemaker if the thermostat is bad. So you don't need to worry about cleaning them periodically such as is needed with air conditioners. We've identified the most common parts that can cause a refrigerator's ice maker to not make ice, but there are other parts that could be at fault. The proper pressure values vary too much on ambient conditions and time into the cycle to be reliably diagnostic of a low charge. The repair man said that it typically breaks and he replaced the part with a more appropriate longer lasting part.


Next

Whirlpool Ice Maker Not Working

whirlpool gold ice maker troubleshooting

These minor kinks will not interfere with the proper cutting action of the grid. . To be sure I did not have a bad new board, I ordered another emitter set and still no lights on the emitter or power to the icemaker. Since the grid is in two halves, one for each direction, the current through any given resistance wire segment is about 1 amp. Considering that a unit could run 50 cycles per day, that could be less than 3 years. The ice maker was turned back on.

Next

How to Troubleshoot the Ice Maker

whirlpool gold ice maker troubleshooting

Click the link below to visit our store and purchase new ones. Likely only the upper level of the grid wire is broken, and you can restrict your repair to that one circuit, since the upper wire breaks from the repeated impact of the ice slab coming off the evaporator; the lower level very rarely breaks since it does not receive any such impacts. Suction cups on the pump mount it onto the bottom of the reservoir. The grid consists of 19 wire segments about 9 inches long each, for a total of 171 inches of active wire. The solder joint has proven adequate on this small tubing and minimizes the contamination from heat oxidation. The shroud can contact the fan blade and make a loud buzzing noise.

Next

Whirlpool Refrigerator Ice Maker Not Working

whirlpool gold ice maker troubleshooting

This improvised timer and relay circuit is a bare-bones control. During harvesting, the water valve opens to refill the recirculating reservoir and flush the used water out via an overflow drain, while the recirculation pump stops. The repair to resolder this bracket is a bit challenging. Often you can fix things better yourself with a little ingenuity. Here is what i Have done to correct problem to no avail: 1. A bit of aluminum refrigeration duct tape, or even cheap duct tape, stuck on the inside of the dried reservoir, would work temporarily if you can't get hold of the stopper part for a while. So make sure this tube is in place.

Next

Whirlpool Refrigerator Repair Questions, Solutions and Tips

whirlpool gold ice maker troubleshooting

Make sure any harvested ice slab makes it all the way down onto the grid and doesn't hang up from being chubby. Another possibility for removing the fan is getting to the fan from the side or behind the unit. Does your freezer light switch work? The rubber may be partly disintegrated or missing altogether. One simply has to remove the grid from the machine and pinch off the lime encrustations with some pliers. You must first remove the cutter grid remove two thumbscrews , reservoir bucket remove two thumbscrews , and recirculation pump remove three acorn nuts at rear wall, disconnect recirculation tube from top of evaporator plate. The rotating fan blade is surrounded by a rather flimsy folded fiberboard shroud that can distort in shape, such as from age or from getting wet.


Next